How Do I Reset The Schedule On My Pentair Intelliflo Pump

Shareholders own approximately 475 of Pentair Ltd. Schedule 5 we shut down at 701 am.

How To Set Up Your Pentair Intelliflo Variable Speed Pump

Make sure that the pump is on.

How do i reset the schedule on my pentair intelliflo pump. After wiring and getting everything running the LCD on Intelliflo VF pump display was minimal. Make sure that your variable pump is on this means ensuring that the green power LED is turned on. The factory settings will be in assigned.

AMPM is set accordingly as you go past noonmidnight. As you can see setting the Date Time on the Intelliflo is really not that complicated. The IntelliFlo pump will not run the scheduled speeds until the StartStop button is pressed LED on to place the pump in the Running Schedule mode.

And the IntelliFlo VSF pump always delivers the precise flow needed for peak equipment performance. Researching it the VF pump when hooked up to a 1x motherboard will cause it. Then how many rpm do you need to run a pool pump.

In this regard how do I reset the schedule on my Pentair IntelliFlo pump. Check that the green power LED is on. Tyco shareholders now own approximately 525 and former Pentair Inc.

Theres no more guessworkjust set the desired flow rate and the pump will adjust as needed. I run my pump this long because I live in Florida and it is consistently hot. Also check the basket lid o-ring to make sure its getting a good seal.

Press and hold the four buttons simultaneously for about 4 seconds. The IntelliFlo VSF pump is the first of its kind to respond to changes in your pools environment in order to maintain a preprogrammed flow rate. Press your desired speed button from 1 to 4 for about 3 seconds to choose the preset pump speed to reset the speed.

The IntelliConnect Control and Monitoring system allows pool owners like you to monitor and control your pool equipment from the user-friendly Pentair Home app from your backyard oasis or anywhere in the world. Power off the unit and restart. The GFCI should interrupt power.

After you set the date and the time you have to scroll again and look for the minimum-maximum. Use the Up or Down arrow button to scroll to Speed 1-8. I have an Intelliflo VSP and I want to set the schedules but cannot seem to get it to run in schedule mode after I save the parameters.

Low speed 1800 RPMS- peak hours The total run time is 14 hours. A program for a typical pool might. Press Save to confirm the changes.

If you clean the filter and pump basket out and still have a problem you need to start looking for the leak. You can easily use its control panel button to preset or even reset your preferred speed. Press the Menu button.

After 96 hours IntelliFlo VF s clock must be reset. Adjusting Screen Contrast Press to scroll to Contrast. I installed a new intelliflo pump last year but only set one schedule on it.

I want to use Program 1 for one schedule Program 2 for another. Avoid setting at 0 unless you are unable to read the screen due to bright sunlight. Push the reset button.

If its less than half way up the skimmer that could be where the air is going. Following this merger the new company was based in Schaffhausen Switzerland with 30000 employees and 100 manufacturing plants in 30 countries. Now I am trying to run 3 on off schedules two at speed 1 and one at speed 2 for a 24 hour period by following instructions in the manual but when I set the second or 3rd schedule it seems to cancel the first schedule.

Controls up to five pool products like pool pumps filtration lights. Unplug the communications cable from the EasyTouch was unable to change the pump back to the full feature menu. IntelliFlo can store the correct time for up to 96 hours after power is shut off.

Press and hold the four buttons simultaneously for about 4 seconds. Power off the unit and restart. To set a schedule to run the pump.

IntelliFlo Variable Speed Pump Factory Resetting. Screen contrast levels can be set from 0-9. In colder states you probably.

Press the stop button the pump will stop. IntelliFlo Variable Speed Pump Factory Resetting. First check the water level in your skimmer.

If the GFCI interrupts power to the pump without the test button being pushed a ground current is flowing indicating the possibility of an electric shock. If the GFCI fails to operate in this manner the GFCI is defective. Do not use this pump.

Furthermore who owns Pentair. Use the Left Right Arrows to cycle between HourMinute and Up or Down Arrows to change the numerical value. Settings will be the first thing you will see on the menu.

Additionally how do I reset the schedule on my Pentair IntelliFlo pump. Secondly how many RPM should I run my pool pump. Mid speed 2200 RPMs- non-peak hours 12 pm.

The overlap will allow whichever pump speed is higher speed to run for that one minute just to avoid the pump trying to shut down and restart quickly. High speed 3450 RPMs to ensure the pump sufficiently primes- non-peak hours 430 12 pm. 4 430 am.

Press the menu button and select Settings. On the settings you can set the date and the time of the pump. Press the stop button the pump will stop.

The factory settings will be in assigned. Its like cruise control for your pump. Power should be restored.

I have the manual and am following the instructions for scheduled run times. Make sure that the pump is on. You would go through the schedule down to speed change your speed if you need to in the speed section select that then you get to the start time with your starting at 7 am.

Press Select to edit.

Programming The Schedules And Speeds On A Pentair Youtube

Share this post